1Electronic Emission NoticesFederal Communications Commission (FCC) StatementThis equipment has been tested and found to comply with the limits fo
10Technical Reference BookletAudio ConfigurationAfter installing the audio driver, you can select 4/6 channel surroundaudio output in the software uti
11In the software utility, double click “AC97 Audio configuration” icon fromthe window taskbar on the right bottom.Then the “AC97 Audio Co
12Technical Reference BookletMethod 2: Using S-BRACKET connectors:The S-Bracket (shown on page 14) is an optional accessory. It gives access toanalog
13The connector allows you to connect a S-Bracket for a Digital Interface (SPDIF).The S-Bracket offers 1 SPDIF jacks for digital audio transmission an
14Technical Reference BookletPIN Assignment DESCRIPTION1 SOUT-L Audio left surrounding output2 SOUT-R Audio right surrounding output3 GND Ground
15Front Panel Audio Header - FPS1This mainboard supports front panel microphone and speaker out ports.If your computer case has these ports, connect t
16Technical Reference BookletCDS11PIN Assignment1 CD-L2 GND3 GND4 CD-RCDS1CD-IN Connector - CDS1The connector is for CD-ROM Drive.
17Jumper SettingsThis chapter explains how to configure the motherboard’s hardware. Before using yourcomputer, make sure all jumpers and DRAM modules
18Technical Reference BookletConnectorsThe motherboard provides connectors to connect to FDD, IDE HDD, and USBPorts and to the CPU/System FAN etc.Flop
19Serial ATA Hard Disk Connectors -SATA-1, SATA-2 (optional)The mainboard has 2 SATA connectors. The mainboard provides dual high-speed Serial ATA int
2Technical Reference BookletTable of ContentsHARDWARE CONFIGURATION ... 4Key Features ...
20Technical Reference BookletSerial ATA Hard Disk Devices Power Cable (optional)Serial ATA Cable (optional)Connect one end of the SATA cable to the ma
211291012910USB1USB2PIN Assignment1 VCC2 VCC3 USBP0-4 USBP1-5 USBP0+6 USBP1+7 GND8 GND9 KEY10 OC#USB ConnectorUSB Connectors - USB1, USB2This mainboa
22Technical Reference BookletFan Power Header - CPUFAN, SYSFANThe CPUFAN1 (processor fan) and SYSFAN1 (system fan) support systemcooling fans using +1
23Front Panel Header - FP1The mainboard provides one front panel connector for electrical connect on tothe front panel switches and LEDs.FP1NCVCCKEYNC
24Technical Reference BookletSlotsThe motherboard provides one AGP slot, two 32-bit PCI bus slots.AGP SlotPCI SlotsAGP (Accelerated Graphics Port) Sl
25CPU InstallationPlease refer to the following steps to install the CPU.1.Use index finger and thumb tomove metal lever so it is separatedfrom the bo
26Technical Reference Booklet4.Use index finger and thumb topress down metal lever, the cap willbe pushed up by the CPU; this mayalso be done by remov
276. It’s recommended that the CPU heatsink should be an approval by Intelcorporation design for Prescott CPU. Choose the orientation of the thermalso
28Technical Reference Booklet9. Gently rotate the cap clockwise1/4 turn.10. At last, attach the fan wireconnector to the 4 pin fan headerconnector on
29Install DDRII DIMMsPlease follow the steps below to install DDRII DIMMs.1. Locate the DDRII DIMM sockets.2. Holding the DDRII DIMM by the edges, rem
3INSTALL DDRII DIMMS ... 29BIOS SETUP ...
30Technical Reference BookletBIOS SETUPAbout the Setup UtilityThe computer uses the latest Award BIOS with support for Windows Plug andPlay. The CMOS
31Main MenuOnce you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on thescreen. The Main Menu allows you to select from various s
32Technical Reference BookletLoad Optimized The chipset defaults are settings which provide for maximumDefaults system performance. While Award has de
33IDE Channel These categories identify the types of the two channels that0/1 have been installed in the computer.If the controller of the HDD interfa
34Technical Reference BookletFrequency/Voltage ControlThis section allows you to set CPU Speed.Set Supervisor/User PasswordYou can set either a superv
35Flash Update ProcedureA program AWDFLASH.EXE is included in the utility diskette or CD (X:\Utility\AWDFLASH.EXE). Please follow the recommended proc
36Technical Reference Booklet SATA RAID User ManualEnter BIOS Configuration UtilityWhen the system powers on, the following information will appear on
37Create Disk Array1. Use the arrow keys to navigate the main menu. Use the up and down arrow keys toselect the Create Array command and press <Ent
38Technical Reference Booklet3. After selected array mode, there are two methods to create a disk array. One methodis “Auto Setup” another is “Select
395. Use the arrow key to highlight Start Create Process and press <Enter>. A warningmessage will appear, press Y to finish the creation, or pre
4Technical Reference BookletHARDWARE CONFIGURATIONKey Features :Chipset• VIA P4M800 Pro+VT8237R PLUS chipset.Processor• Supports Intel® Celeron® , Pe
40Technical Reference Booklet VIA Tech. VT8237 Series SATA RAID BIOS Ver 4.90&Create Array Sct/Clear bootable array&De
41Rebuild Broken RAID 1 ArrayWhen booting up the system, BIOS will detect if any member disk drives of RAID hasfailed or is absent. If BIOS detects an
42Technical Reference Booklet1. Power off and Check the Failed Drive:This item enables users to turn off the computer and replace the failed hard driv
43DRIVER AND RAID SOFTWARE INSTALLATION1. After Windows has finished booting up, the system will automatically findthe newly installed adapter and
44Technical Reference BookletInstall Operating System into SATA HDDInstall Windows NT 4.0,2000,XP1.Insert the bundled driver CD DISC into CD-ROM(G:).
5Serial ATA/RAID Controller (optional)• Complies with Serial ATA Specificaion Revision 1.0.• Two ports supported two S-ATA devices.• Support RAID Conf
6Technical Reference BookletIntegrated UnichromeTM Pro GFX /Video Accelerator• Optimized Shared Memory Architecture (SMA).• 16/32/64MB frame buffer us
7Motherboard LayoutThe following diagram shows the relative positions of the jumpers, connectors, majorcomponents and memory banks on the motherboard
8Technical Reference BookletRear PanelThe back panel provides the following connectors:Mouse ConnectorThe mainboard provides a standard PS/2® mouse m
9Serial Port Connector: COMThe Port is 16550A high speed communication ports that send/receive 16bytesFIFOs. You can attach a serial mouse or other se
Komentarze do niniejszej Instrukcji